Jump to content
  • Welcome, Guest!

    Welcome to Backcountry 4x4's online community! Consider creating a free account to take part in our discussions, share photos / videos, and start "web wheeling" with us!

My 05 Rubi build. Slow like a 4.0


Recommended Posts

So I'm thinking about making a run to the u-pull to grab a few things.  I've been thinking about getting front coil springs, and tie rod assy from a V8 ZJ.  I know the tie rod assy is a good upgrade, but I've been reading different things on the coils.  The stated lift they give ranges from 1"-3".  I have 2" spacers in mine now, and I'm happy with how the rear sits, but I'd like to get rid of the rake, which means I need to go another 0.75"-1" higher in the front.

 

I'm sure that with some combination of the coils with the ZJ coil isolators, or my BB will work.  I guess it'll just be trail and error figuring out what will work. Hell, even if it still just gives me 2", it should flex a bit better than the stock coils with the spacers.

  • Like 3
Link to post
Share on other sites
  • Replies 649
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Popular Posts

Today I made a set of bar pin eliminators, put the JK front shocks in, took both front coil spring isolators out and replaced them with the 2" coil spacers that were in there before. It's now sitting

Here's hoping these will hold too.   The second front fender is welded up.  I screwed up when I first started tacking the skin on, and had to cut it off.  Luckily I only had about 5 tacks do

Finally got my light bar mounted today.  

Posted Images

Its wonderful being able to mix and match like that! 

I don't know if there is anything I want at this candy store, but I should go see it sometime!

  • Like 1
Link to post
Share on other sites
8 hours ago, derekmac said:

Here are before/after pics I found online.

Before, stock springs and 2" spacer.

BeforeZJSprings007.jpg

 

After, with V8 ZJ coils.

After005.jpg

 

That would be about perfect for me.

These pictures show absolutely no difference in height... But he did eliminate the spacers there in the front... The only change is the angle and distance it was taken from...

 

For the tie rod, you are better off buying new, with new end and adjuster sleeve. They are not overly expensive, mine was $85 before tax and shipping when I ordered it from autopartsway for all 3 pieces. I added a blower resistor to it to bring it up in total to get the cheap shipping...

  • Like 1
Link to post
Share on other sites

The slight angle difference in the pics would exaggerate it some, but not enough to make that difference shown. There's definitely a slight increase in height, which is all I'm after. 

 

A tie rod assy is only $6.75 at Kennys. I'll pull one, and if the ends are still pretty tight, I'll grab it. If nothing else, it'll make for a good spare. 

  • Like 3
Link to post
Share on other sites

So I made it to Kenny's today, and there was an V8 Limited ZJ there. :)  I pulled the coils and isolators out of it, and I also found a half decent Pioneer deck in another rig that I grabbed.  I don't mind if a $20 junkyard deck gets stolen, but I wouldn't be happy if I bought a new one, and it got ripped out.  Now I just need to get a wiring harness for it, and it'll be good to go. :) 

  • Like 3
Link to post
Share on other sites

I need at least one radio, for the Scout. It had an AM radio.  Some folks may have to look that up as 'in the olden days', lol.

Got some other ideas, must go there!

  • Like 1
Link to post
Share on other sites
1 hour ago, sar4x4 said:

I need at least one radio, for the Scout. It had an AM radio.  Some folks may have to look that up as 'in the olden days', lol.

Got some other ideas, must go there!

I listened to 960 (CHNS?) growing up. :) 

 

They had another half decent Panasonic radio in a truck there.  I took it out as it was in a Dakota, and the adapter plate was the same as what I needed for the Jeep.  I doubt it'll last long just sitting there.

Link to post
Share on other sites

I installed the ZJ springs tonight, and they lifted it another 0.5".  Not as much as I wanted, but better than nothing.  I could take both (stock and ZJ) coil isolators out, and put just the 2" coil spacers in, and it'll sit exactly how I want.

  • Like 2
Link to post
Share on other sites
1 hour ago, sar4x4 said:

I need at least one radio, for the Scout. It had an AM radio.  Some folks may have to look that up as 'in the olden days', lol.

Got some other ideas, must go there!

I have a Kenwood cd player u can have Eugene 

  • Like 1
Link to post
Share on other sites

I was also going to install the stock JK shocks in the front, but I didn't feel like fighting with swapping the bar pins over.  I might just try and find a set of bar pin eliminators for them.

Link to post
Share on other sites
7 minutes ago, BLAZZING-XJ said:

I have a Kenwood cd player u can have Eugene 

 

We need to meet up sometime!  I also owe you a phone call, but whatever you needed it's probably too late now!  Oh dear.  You seem to meet up with Deborah quite often at the liquor store, lol.

Link to post
Share on other sites
4 hours ago, sar4x4 said:

I need at least one radio, for the Scout. It had an AM radio.  Some folks may have to look that up as 'in the olden days', lol.

Got some other ideas, must go there!

I have an aftermarket deck you can have Eugene. I'll check the garage tomorrow.

  • Like 1
Link to post
Share on other sites
  • 2 weeks later...

Today I made a set of bar pin eliminators, put the JK front shocks in, took both front coil spring isolators out and replaced them with the 2" coil spacers that were in there before. It's now sitting at 3" over stock in the front, and the rake is now gone. :) 

 

 

image.jpeg

image.jpeg

image.jpeg

  • Like 6
Link to post
Share on other sites
2 hours ago, Jawritch said:

Those BPE's look really good, good job!

 

Thanks! I was going to buy a set, but I figured I was better off paying $7 for a piece of metal and making my own, compared to paying over $60 for a set. Mine might not look as pretty as ones you buy, but they should do the trick. 

  • Like 1
Link to post
Share on other sites
4 hours ago, derekmac said:

Thanks! I was going to buy a set, but I figured I was better off paying $7 for a piece of metal and making my own, compared to paying over $60 for a set. Mine might not look as pretty as ones you buy, but they should do the trick. 

 

I only paid $40 for my RC ones, but that was back when the exchange rate was at par or better... 

Link to post
Share on other sites
18 minutes ago, jay said:

Nothing wrong with that :)

Could ya sell the 31's to go towards some 33's?

I could, but not sure if the evil wife eye would be worth it!! lol

 

I think I want to get a body lift in first though, so I won't have to worry about clearance issues.

  • Like 4
Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...