FJ60Toy Posted May 17, 2015 Report Share Posted May 17, 2015 I have a set of m12 x 1.25 lugs that I used to mount toyota wheels on my Xterra I almost tossed them out a while ago Link to comment Share on other sites More sharing options...
SQRLPWR Posted May 17, 2015 Report Share Posted May 17, 2015 I wish I'd seen this earlier...I've already ordered a set...but thanks anyways :) Link to comment Share on other sites More sharing options...
SQRLPWR Posted May 17, 2015 Report Share Posted May 17, 2015 Common lug nut for Toyota. Get these ones, the washer stays on the lug. There are a lot of variation in sizing out there. Toy Nuts.jpg Thanks, Toy is m12 1.50 ... mine are m12 1.25 - Rockauto just go by make/model and don't list the shank sizes. I don't normally order from ebay but I found an exact shank size match - I've ordered these http://www.ebay.ca/itm/24-Chrome-Mag-Seat-Lug-Nuts-For-Nissan-Factory-OEM-Aluminum-Wheels-M12x1-25/141398323670 Link to comment Share on other sites More sharing options...
SQRLPWR Posted May 18, 2015 Report Share Posted May 18, 2015 Got the Yokohama Geolander M/T's mounted, and I have to say I've become an instant fan!! The 265/75r16 tires are an inch taller and comparable in width to the 31x10.50r15's, and I really like the tall look too :) Before with Goodyear Wrangler Territory 31x10.50.r15's After with Yokohama Geolander M/T 265/75r16's - I could not be happier!!!! :) With my 2 inch suspension lift, no body lift and no front mud guards, the only trimming I may need to do is on the rear mud guards/bumpers. Link to comment Share on other sites More sharing options...
My04T4R Posted May 18, 2015 Report Share Posted May 18, 2015 Right on! Those and the rims look awesome! Still got a bit of tread life left in em! Link to comment Share on other sites More sharing options...
SQRLPWR Posted May 18, 2015 Report Share Posted May 18, 2015 yes, thank you so much!! :) Link to comment Share on other sites More sharing options...
My04T4R Posted May 18, 2015 Report Share Posted May 18, 2015 Hey don't mention it just have fun with them hopefully they will make a good difference for the x Link to comment Share on other sites More sharing options...
Jake Posted May 18, 2015 Report Share Posted May 18, 2015 Tires and rims look great. As for me, i greased everything on the jeep that has a zerk fitting...and started prepping for the rear floor and frame repair. Link to comment Share on other sites More sharing options...
derekmac Posted May 18, 2015 Report Share Posted May 18, 2015 That looks wicked Jay!!!! Should make a good amount of difference in the woods too! Link to comment Share on other sites More sharing options...
TacoMitch Posted May 18, 2015 Report Share Posted May 18, 2015 I know where you're flexing!! Tires look great! I'm sure you'll notice a huge difference now! Link to comment Share on other sites More sharing options...
simon Posted May 18, 2015 Report Share Posted May 18, 2015 Looks great jay! Link to comment Share on other sites More sharing options...
SQRLPWR Posted May 18, 2015 Report Share Posted May 18, 2015 I know where you're flexing!! gotta love no front or rear swaybars :) Link to comment Share on other sites More sharing options...
SQRLPWR Posted May 18, 2015 Report Share Posted May 18, 2015 If forgot I took this photo to show the size difference :) Link to comment Share on other sites More sharing options...
My04T4R Posted May 18, 2015 Report Share Posted May 18, 2015 Any change in ride characteristics? Link to comment Share on other sites More sharing options...
SQRLPWR Posted May 18, 2015 Report Share Posted May 18, 2015 took the rear quarter plastics off to see if there was any opportunity for trimming them for the bigger tires, and there isn't But I managed to straighten out the dented corner - by standing on it from the inside ROFL :) :) :) Link to comment Share on other sites More sharing options...
SQRLPWR Posted May 18, 2015 Report Share Posted May 18, 2015 Any change in ride characteristics? Hard to tell, I've not done many KMs on them yet. I'm taking Lewis to soccer training in Weir Field in a few. There's a quarry in Mt. Uniake quite close by, so I'll go and have a play whilst I wait for him to finish ;) I would have struggled to climb that rock with my GY's tho as the ground was gravel....but that could also have been my Lokka helping out a bit too :) Link to comment Share on other sites More sharing options...
robicon Posted May 18, 2015 Report Share Posted May 18, 2015 Nice upgrades Jay! Link to comment Share on other sites More sharing options...
robicon Posted May 18, 2015 Report Share Posted May 18, 2015 So as always I am slow on uploading pics. Here is the dual battery setup. The pillar switch allows me switch between charging both batteries or jumping the primary if it's dead from the secondary. Today, Emily and I tackled cutting the fenders. Only been wanting to do this forever and final just did. Turned out fairly well! :D Link to comment Share on other sites More sharing options...
Brunet-Hemi Posted May 18, 2015 Report Share Posted May 18, 2015 Well done with the fenders and battery. Get that issue you had with batteries sorted? Link to comment Share on other sites More sharing options...
BLAZZING-XJ Posted May 18, 2015 Report Share Posted May 18, 2015 Picked up some used 315/75/16 fore the avalanche. Now need to get them changed over . Link to comment Share on other sites More sharing options...
derekmac Posted May 18, 2015 Report Share Posted May 18, 2015 Looks good Robbi! Link to comment Share on other sites More sharing options...
FJ60Toy Posted May 19, 2015 Report Share Posted May 19, 2015 Jay your Xterra reminds me of the one I used to have about 8 years ago. I liked it a lot. Check out the wheels I had on it. I ran 235 85 16 Dayton timberline MT. Tires Link to comment Share on other sites More sharing options...
SQRLPWR Posted May 19, 2015 Report Share Posted May 19, 2015 Wow, same fronts...very cool coincidence :) Yours makes me feel the need to tackle my front bumper next ;) Link to comment Share on other sites More sharing options...
FJ60Toy Posted May 19, 2015 Report Share Posted May 19, 2015 Yeah I was surprised when I saw those wheels on your truck. Do you have a rear locker or factory limited slip? I had added one or two extra plates to my rear limited and it worked really well. My bumper was not great looking but it did the job. The rock sliders I made for it saved it from lots of damage. Link to comment Share on other sites More sharing options...
SQRLPWR Posted May 19, 2015 Report Share Posted May 19, 2015 Today, Emily and I tackled cutting the fenders. Only been wanting to do this forever and final just did. Turned out fairly well! :D They look nice and aggressive! :) Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.